🔥 Your Fuel & Usage

Enter therms from your gas bill.
AFUE for a furnace or boiler; COP × 100 for a heat pump.
Check your local climate data; 5,000 is a mid-Atlantic baseline.

💰 What Winter Costs

Annual heating cost$880
Cost per million BTU delivered$11.79
Cost per sq ft heated$0.59
Heating intensity (BTU / sq ft / HDD)9.955 BTU/ft²/HDD
Delivered BTU per year74,664,000 BTU
Compare the cost per million BTU against the table on the Examples tab. That number ignores your house and your climate entirely — it is purely the price of heat from this fuel at this efficiency.

📊 Worked examples

Five homes, five fuels, one comparable number

The only column that can be compared across rows is cost per million BTU. Annual cost differs because each house burns a different amount of fuel — a big house with a cheap fuel can cost more than a small house with an expensive one.

ScenarioFuel usedAnnual costCost per million BTU
Natural gas, 800 therms @ $1.10, 90% furnace800 therm$880$12
Heating oil, 600 gal @ $4.10, 85% boiler600 gal$2,460$35
Propane, 900 gal @ $2.60, 92% furnace900 gal$2,340$31
Electric resistance, 9000 kWh @ $0.17, 100%9,000 kWh$1,530$50
Heat pump, 6000 kWh @ $0.17, COP 300%6,000 kWh$1,020$17

The heat pump row is the interesting one. It uses the same $0.17 per kWh as the resistance row but delivers three times the heat per kWh, so its cost per million BTU is roughly a third. That gap — not the sticker price of the equipment — is what decides whether a heat pump pays for itself.

📊 Same heat, different fuels

What 60 million BTU delivered actually costs

Here every fuel is asked to deliver exactly 60 million BTU into the house, which is roughly a 1,500 sq ft home in a 5,000 HDD climate. Prices are typical 2026 US averages; substitute yours.

FuelUnits needed for 60 MMBtuAnnual cost
Natural gas643 therm$707
Heating oil509 gal$2,087
Propane713 gal$1,853
Electric resistance17,584 kWh$2,989
Heat pump (COP 3.0)5,861 kWh$996

These figures use delivered heat, so the furnace efficiency is already inside the unit count — an 85% oil boiler needs more gallons than the raw BTU math suggests. If you are quoted a price per gallon without an efficiency figure, you are comparing the wrong number.

📖 Why price per gallon is a misleading number

Every fuel holds a different amount of heat

A gallon of heating oil contains about 138,690 BTU. A gallon of propane contains about 91,500. A therm of natural gas contains about 103,700. A kilowatt-hour of electricity contains 3,412 BTU no matter how it was generated. Because the units differ, the price per unit is not comparable — you have to normalise to BTU before the numbers mean anything.

Cost per MMBtu = (Units × Price) ÷ (Units × BTU per unit × Efficiency ÷ 1,000,000)
The units cancel, so this reduces to Price ÷ (BTU per unit × Efficiency) × 1,000,000. That is why the answer depends only on fuel price and efficiency — not on how much you burn.

Efficiency is the second multiplier, and it is brutal

An old atmospheric gas boiler at 70% AFUE throws away 30 cents of every dollar up the flue. A modern condensing furnace at 96% keeps almost all of it. Replacing a 70% boiler with a 96% furnace cuts the gas bill by roughly 27% with no change in comfort — a bigger gain than most people get from shopping around for a cheaper supplier.

Heat pumps break the pattern because their "efficiency" exceeds 100%. A unit with a seasonal COP of 3.0 moves three units of heat for every unit of electricity, which is why the number behaves more like 300% in the efficiency field. Do not enter the nameplate HSPF rating directly — convert it (roughly HSPF ÷ 3.412 = COP) or use the manufacturer's seasonal COP.

What the calculator cannot see

This tool prices heat. It does not price the equipment, the install, the ductwork, or the electrical panel upgrade a heat pump may require. A heat pump that costs $6,000 more to install but saves $600 a year has a ten-year payback before any incentive — and many states and utilities now cover a large share of that gap. Run the annual-cost number first, then subtract incentives from the capital cost separately.

📝 How to use this for a real decision

Step 1 — get your real usage. Pull twelve months of bills, not one. Heating usage is heavily seasonal, and a single January bill extrapolated across a year overstates everything.

Step 2 — find your actual delivered price. Use the total bill divided by total units, including delivery charges, taxes and fees. The commodity price on the front page of the bill is not what you pay.

Step 3 — enter seasonal efficiency, not peak efficiency. A furnace rated 96% AFUE may run at 91% in a mild climate where it short-cycles. Use the AFUE for furnaces and boilers; use seasonal COP for heat pumps.

Step 4 — compare in cost per million BTU, then decide. If two fuels land within about 10% of each other, the decision is about capital cost and comfort, not operating cost. Only a gap wider than that justifies switching equipment.

Frequently asked questions

Why is my cost per million BTU different from a table I found online? ▾
Those tables usually assume a single national average price and a fixed efficiency. Your delivered price includes distribution charges and taxes that vary enormously by utility and state, and your equipment's actual efficiency may be well below nameplate. Substituting your own two numbers is the whole point of this calculator.
Should I enter AFUE or the rated efficiency on the sticker? ▾
Use AFUE for furnaces and boilers — it is already a seasonal figure that accounts for cycling and standby losses. For heat pumps, do not enter HSPF; convert it to COP by dividing by 3.412, then multiply by 100 to express it as a percentage.
Does the heated floor area change the cost per million BTU? ▾
No. Cost per million BTU is a property of the fuel and the equipment only. Floor area is used for the cost-per-square-foot and heating-intensity figures, which tell you whether your house is leaky relative to its size. A high intensity usually means air sealing and insulation will beat a fuel switch on payback.
Why does a heat pump show efficiency above 100%? ▾
A heat pump does not create heat, it moves it. For each unit of electricity it can move two to four units of heat from outside into the house, so the ratio of heat delivered to energy consumed exceeds one. Entering 300 in the efficiency field represents a seasonal COP of 3.0.
Should I include the fixed monthly service charge? ▾
Exclude it when comparing fuels, because a fixed charge does not scale with how much you heat and would distort the per-BTU figure. Include it when you are budgeting the actual annual cash outlay, which is a different question from which fuel is cheaper.
⚠️ Important note

This calculator prices energy, not equipment. It does not include installation, maintenance, ductwork, electrical upgrades, or available rebates and tax credits, all of which can change a fuel-switching decision substantially. Fuel prices vary by region and season and should be taken from your own bills rather than national averages.